Cabinets cutting template
Refrigerator Surround Cabinet Cut List Template
A refrigerator enclosure with tall side panels, bridge cabinet, ventilation and door-swing clearance, and a removable service path. Use this as a starting point, then change every dimension for your room, hardware, material thickness, and joinery before cutting.
Release boundary for this template
Do not release these plywood parts from nominal dimensions alone. Close the measurement, system, and installation decisions first.
- Field measurement: Measure the finished appliance bay at floor, counter, and top heights after flooring and wall finishes are known.
- Hardware and service system: Approved refrigerator data controls clear opening, air path, hinge clearance, service route, and bridge height.
- Installation boundary: Side panels and fillers are scribed only after the appliance bay is level, square, and checked for removal access.
Use Field-measure the appliance enclosure to prepare the input, and Diagnose an appliance bay that is too small if the drawing, hardware, or installed condition no longer agrees.
Plan the refrigerator surround cabinet before buying sheets
Start by confirming the finished width, depth, height, access clearances, and load requirements. This template is intentionally made from rectangular plywood parts so you can adapt it without redrawing the whole project. Keep matching pieces grouped together, mark visible faces, and leave room for edge banding, backs, doors, drawers, hinges, or trim that apply to your version.
Use 3/4 inch plywood for the structural parts unless your design calls for another thickness. A template is not a structural rating: add bracing, wall anchoring, weather protection, or a thicker panel whenever the location, load, or local requirements demand it.
Refrigerator Surround Cabinet project-specific checks
Use these checks with the sample parts list before calculating sheet count or making a purchase.
- Use the appliance guide for ventilation, hinge-side clearance, door opening angle, handle projection, water line, outlet, and leveling access.
- Confirm the refrigerator can be removed without dismantling fixed countertop, crown, flooring transitions, or adjacent cabinet faces.
- Size the bridge cabinet and structural support independently from decorative side panels and refrigerator top trim.
- Keep field-sized fillers available for wall bow, appliance centering, and neighboring handle clearance.
Refrigerator Surround Cabinet parts list
Material: 3/4 in plywood
Kerf allowance: 1/8 in between cuts
Grain direction: keep visible faces consistent
Part | Size (in) | Qty
-------------------+-----------------+----
Tall side panels | 24 x 84 | 2
Bridge cabinet sides | 24 x 18 | 2
Bridge top and bottom | 22-1/2 x 36 | 2
Bridge back rail | 4 x 36 | 2
Side fillers | 4 x 84 | 2Review each part against the actual construction method before cutting. Reduce a shelf or bottom for side-panel thickness where needed, leave back-panel or drawer-slide clearance, and make a test piece for any groove, dado, or hardware opening. Label repeated parts as a batch so their orientation stays consistent.
Check the sheet layout and cut order
Place the largest parts first, then nest matching rectangles around them. Square footage alone cannot tell you the sheet count because saw kerf, grain direction, and the shape of the remaining offcuts matter. Enter this adjusted list in the plywood cut calculator with your real sheet size and blade kerf before purchasing material.
Break full sheets into manageable strips first, then crosscut the final parts. Keep pairs together, label the inside faces, and dry-fit the case on a flat surface before driving final fasteners. The cut list calculator is useful if the project also uses solid-wood rails, trim, or stretchers.
Assembly checks that prevent rework
Dry-fit the major panels, measure both diagonals for square, and confirm that moving parts or equipment have the clearance you planned. Pre-drill near plywood edges, test fasteners in an offcut, and attach the back only after the cabinet or frame is square. Read how to read a cut list and saw kerf explained if you need a refresher before finalizing the layout.
How this template was prepared
The parts list models a common refrigerator surround cabinet carcass or frame so you have named pieces and repeated quantities to review. It deliberately leaves hardware, joinery, edge treatment, structural loads, and site conditions open because those choices change final dimensions. Before cutting, verify every opening and finished dimension, confirm material thickness with a caliper, apply hardware clearances, and review the optimized layout against the drawing or room. For a transparent comparison of common template inputs, see the plywood project yield benchmark.
Make this template yours
Replace the sample refrigerator surround cabinet dimensions with the real job
The sample rows are a planning start. Create a CutList project with the measured dimensions, actual material, blade kerf, grain direction, and approved quantities before releasing parts.
- Free basic layouts
- No login
- No cloud upload
- Works offline
On a computer? Scan with your iPhone or iPad.
More project templates
Browse the full plywood cut list template library for related builds, then save a revised version in the CutList optimizer app when you want to compare sheet counts or keep the plan for later.